To rationalize and optimize the treatment cycles are available on request optional systems, such as:
MOTORIZED DOORS AT VERTICAL OPENING
it is possible to install doors at vertical opening with frontal flatcar for the load with overhead travelling crane.
MUD DREDGE AND CHIP REMOVER
placed on the bottom of the storage tank, they are used to remove the chips and mud resulting during the wash process.
for particularly elaborate cycles it is possible to install more reservoirs in monoblock or externally according to the demands of the client.
LANCE OF MANUAL WASHING
with the open door it is possible to work with lance of manual washing connected to spraying pomp.
In normal use of a system based on defined and programmed production times, it can be very useful to install a weekly Clock. This has to make an impact on the heating and / or the ventilation system so the ignition and the shutdown of these units can be planned.
also at tall pressures it is possible to install nozzles at fast dismantlement to perform operations of cleaning.
PLC AND MODEM
In the case of special automation, the machine can be equipped with a PLC, touch screen and modem for remote data transmission and a communication services via SMS.
METERING DEVICE PUMP
Pumps with a low flow rate, which brings the detergent into the storage tanks to compensate the loss or deterioration of the product.
HEATING TO LOW DISSIPATION
Because of the abundant presence of deposits, to protect the devices against the heating, it is important to use the heating elements with large surface areas and low degree of dissipation.
usually included in the degreasing tanks, separator of oil divides water from oil (no emulsion) in order to increase the life of cleaning solution. The circuit is composed by a pump that take the liquid from a tank of the plant through a device that always follows the level and send the liquid to the separation device. From the separation device the water come back to the tanks and the oil goes in an external tank.
for special requirements it’s possible to install filters with degree of retention 1 to 100 microns. On these machines are usually installed bag filters fed by an independent pump that aspires liquid from the treatment tank, pushed it in the filters and re-send it back in the tank.
DRYING And/Or BLOWING
in series at all the machines it is possible to install a system of drying and/or blowing at circulation of warm air.
PORTHOLE OF INTERN VISUALIZATION
MASKS OF SPRAYING
If the components to treat require a precisely localized cleaning, it is possible to install the special pipelines that allow to affect the critical points with high pressure.
In the case of a not waterproof floor, it is possible to installed a tub with a booster pump, which should serve to catch the accidental loss of fluid.
SEPARATOR OF OIL
Included mainly in the degreasing baths, serve to separate the oils from the cleaning solutions in order to extend the life of the latter.
the basin is a container that, when the fixed basket, or the drum, are been charged by the carriage, is be set below with the purpose to pick up the possible draining liquids avoiding that these fall in the adjacent baths, polluting them. The insertion of the basin is programmable for every movement of the carriage.
TURN UP BEDFRAME HEAD
particularly useful to interface the plant with alternative systems of loading and unloading.
are comfortable to facilitate the control and the maintenance of the baths of treatment.
Placed in the containers to maintain a homogeneous treatment solution as from the chemical as well as from the thermal point of view.
MULTI COMPARTMENT DRUM
to contemporarily treat different types of pieces, drums can be separated in more compartments.
SYSTEM OF AUTOMATIC LOADING/UNLOADING
This system is an automatic device, additionally to the machine, for the storage of the equipments in entry and in exit. It allows to make the machine work autonomously without the supervision of an operator.
if necessary is possible to install ultrasounds in the vats of treatment both to side that on fund of the vats.
normally realized with double chamber heated by resistances at bath of oil, is useful to have a great uniformity of heat diffusion, or if the bath of treatment has problems when the sources of heating are too concentrate.
RINSE WATER CONTROL
with the purpose to preserve the waters of rinse it is possible to introduce valves that open at the renewal only in presence of the basket in the vat.
AUTOMATIC TOP UP
system of automatic water top up, that allows to maintain constant the level of liquid inside of the vat.
INSIDE VAT LIFTING
such device, particularly useful for the phosphating, produces a vertical movement of the basket / drum inside of the vat, favoring the renovation of the solution of treatment nearest to the pieces to treat.
especially for plant of great dimensions could be useful move the controls in more comfortable zones, distant from the electric panel. For this is possible to add consoles of remote control endowed with display.
[button color=”view-over-the-town-1″ icon=”info-sign” href=”https://www.ceever.com/en/request-information”]More info[/button]